Français

Questions & Answers

EVO-FORT1 Starts, then stops 2011 Ford Taurus SEL

EVO-FORT1 just installed on a 2011 Ford Taurus SEL. Car remote starts and runs for several seconds, then shuts off. Starts a second time, same thing, shuts off after severall seconds.

I notice that about the time it shuts off is when the dash instruments start to power on. It seems like they power on late. I am wondering if it is trying to read the tach and because the dash powers on late (or at least seems late) . . . it thinks the car isn't running. Just a guess.

Anyone experienced this before? Any ideas?

asked Jun 26, 2016 in Ford by Matthew Mangels (140 points)

1 Answer

Was the module programmed using 1 or 2 keys?

If you sit inside the vehicle and remote start it with the head of the key infront of the ignition barrel does the vehicle stay running?

Aside from the t-harness what other connections were made inside the vehicle?

answered Jun 27, 2016 by derek g (339,570 points)

Thanks for the reply Derek.

Module was programmed with 2 keys.

Just tried remote start with key head in front of ignition barrel, same symptoms.

Aside from the T-harness, I connected to the can high, can low, and driver door pin.

commented Jun 27, 2016 by Matthew Mangels (140 points)

What wires did you connect to at the OBD II?

commented Jun 27, 2016 by derek g (339,570 points)

can high and can low. I attached a screenshot of the diagram I was following that shows the OBDII.

commented Jun 27, 2016 by Matthew Mangels (140 points)

Do you have a flash link updater?

The can bus wires in your vehicle, did the wire color match what was shown in the guide?

commented Jun 27, 2016 by derek g (339,570 points)

No flash link updater :(

And yes. Colors matched up.

commented Jun 27, 2016 by Matthew Mangels (140 points)

Did you connect anything to the yellow/black wire coming out of the t-harness?

commented Jun 27, 2016 by derek g (339,570 points)

Not the yellow/black. The yellow out of the t-harness connected to the yellow out of the 20 pin, but nothing on the yellow/black.

commented Jun 27, 2016 by Matthew Mangels (140 points)

The only other thing I could see that may cause a problem is that your module is currently flashed for a ford mustang, the module checks the vin of the vehicle and if its looking for a mustang vin when its in a taurus this will cause problems. This can be checked here http://fortin.ca/en/support/001A06571675/

So the next step would be to flash the module using the flash link updater-2 for the correct vehicle.

commented Jun 27, 2016 by derek g (339,570 points)

Interesting. I bought it online. Seller said they'd flash it to my specific vehicle. I think I should follow up with them. Lemme see where that gets me. Thanks for the lead.

commented Jun 27, 2016 by Matthew Mangels (140 points)

After troubleshooting with the seller, he determined that the module had A5 enabled. The Fortin guide http://fortin.ca/download/32171/evo-all_ig_tsa_bi_for1-40bits_b_32171.pdf clearly says this should be disabled although is doesn't exactly say it will cause the symtoms I've described. Rather than sending the module back to the seller to flash it, he is going to send me the Flashlink adapter to flash it myself. Even though the guide doesn't say the car will shut off with A5 enabled, the idea that it could be the cause doesn't seem far fetched to me. Thoughts?

commented Jun 28, 2016 by Matthew Mangels (140 points)

A5 is for arming and dis arming the vehicle, but it should be set according to the installation guide, either way once you get the flash link youll be able to set the module up properly for your vehicle...

commented Jun 28, 2016 by derek g (339,570 points)

I'm having the same issues as above and disabling A5 didn't seem to help. Any other ideas?

commented Dec 10, 2016 by Andrew J (180 points)

...